Electrical Cable & Wire

Street Lights & Poles

Solar Products & Systems

Laboratory Equipments

Agriculture Tools Sprayers

Analytical Equipments

Construction Equipments

Dairy & Milk Equipments

Education Equipments

Medical & Surgical

Soil Material Testing Equipments

Microscope

Oil Petroleum Testing Equipments

Pharmaceutical Testing Equipment

Automobiles & Spare Parts

Furniture

Office Equipment

Satellite Communication

PPE Equipment

Fire Fighting Equipment

Gym Equipment

General Relief Products

Material Testing / Geotechnical Equipment

Cube Mould

Code : BHI-CSC- 292

Technical Specifications
Material testing equipment are available in different sizes and are made according to Indian and British Standards. for the metric size cube moulds, the faces are machined flat to + /- 0.02mm accuracy and finished to within 0.2mm for the inch size moulds, the faces are machined flat to +/-0.01 inches and finished to within 0.01 in All moulds are supplied complete with base plate.

Direct Shear Appartus

Code : BHI-CSC- 272

For determinant the direct shear strength of soils on specimen size 60mm x 60mm x 25mm.

Technical Specification
The apparatus comprises of the following. Loading Unit : Supplied with load yoke with direct and lever system for applying load. Normal stress capacity 8kg/sq.cm. load is applied either directly or through a counter balanced detachable lever. Provision is made for the load to be applied either through a steel ball recessed in the loading pad or direct through a boss on the pre collaborated loading yoke. The loading unit is provided with V strips and roller strips for frictionless movement of shear box housing. .

Shear Box Assembly
Comprising Direct Shear box in two halves for a square specimen size 60 x 60 x 25mm one pair of plain gripper plates, one pair of perforated gripper plates, one pair of porous stones, one top loading pad. Shear box housing: Accommodates the Direct shear Box assembly. Complete with two ball roller strips.

Specimen Cutter
For cutting 60 x 60 x 25mm specimen form larger samples. Set of weights to give a normal stress of 3kg/sq.cm. through levger as follows.

Essential Accessories
High sensitivity compression proving ring cap 200kg One consolidation dial gauge 0.01 mm x 25mm and one strain dial gauge 0.01mm x 25mm and one strain dial guage 0.01mm x 25mm.

Optional extras
Additional set of weights to give a normal stress of 5kg/cm2 Soil Sampler for 60mm x 60mm specimen and test forms pad of 50.

Spares
Porous stone for 60mm x 60mm size sample available in pairs

Specimen Cutter «
For cutting 60 x 60 x 25mm specimen form larger samples. Set of weights to give a normal stress of 3kg/sq.cm. through levger as follows.
To give Kg/cm.sq.	Qty.
0.05	4 Nos.
0.1	No.
0.2	1 No.
0.5	3 Nos.
1.0	1 No.

Mortar Penetrometer Astm C : 403

Code : BHI-CSC-196

It is used for finding out the rate of hardening of mortars sieved form concrete mixtures, by means of penetration needles of different cross sectional areas.

The instrument consists of a barrel housing a calibrated spring and a stem graduated from 0-70 kg x 1kg. six interchangeable penetration needles of areas 645,323,65,32,and 16mm sq. are provided. The penetration resistance is measured by the force exerted to penetrate the mortar by 25mm and is indicated by a sliding ring on the stem, which is graduated. Needle shanks are marked at every 12.5mm. compete in a wooden carrying case.

Laboratory Concrete Mixer (Motorised)

Code : BHI-CSC-052

Salient Features
Concrete mixer laboratory type, electrically operated. Designed to remove the burden some work of hand mixing. Uniform thoroughly mixed batches can be produced. The counter balanced drum is easy totilt 1. ½ to 2cu. Ft. mix. The total drum volume is however 3cu.ft.Mounted on a strudy rubber tyred stand, and the drum is mounted for end discharge and equipped with end towing pole. Equipped with ½ h.p. electric motor. Suitable for operation on 220/230 volts A.C. single phase.

Vibrating Machine

Code : BHI-CSC-124

Concrete moulds are cast by using a tamping bar or a vibrating table. However air trapped in cement mortar paste can not be thus removed while casting cement mortar moulds. Easy method is to impart greater vibration of lesser amplitude to the mould while casting. This is achieved in a Vibrating Machine. Vibrating Machine is used for the preparation of mortar cubes for the determination of compression strength of ordinary and rapid hardening Portland cement, low heat portland cement, portland blast furnace cement and high alumina cements.

Technical Specification
the machine consists of a vibrating frame assembly and an electric motor mounted on a sturdy base. The complete frame assembly consists of a vice to hold a 7.06cm cube mould and two studs threaded at top and a hopper to feed the sample in the mould. This assembly is supported on four springs and has an in built rotating shaft which rotates eccentrically and thus imparts vibrations to the entire frame. A balance weight is an integral bottom part of the frame. The centre of gravity of the assembly is brought to the centre of the eccentric shaft or within a distance of 25mm below it. The electric motor drives the shaft of the frame and thus imparts required vibrations to the mould. The frequency of vibration is 12000 ±400 vibration per minute. Supplied complete with on 7.06cm cube mould with loose base plate, a time switch 0-5mins x 1 min and certificate of vibration from a standard laboratory. Spares : Set of Springs, Belt and Belt guard.

Product Range

Laboratory Equipments	Agriculture Tools Sprayers	Analytical Equipments
Construction Equipments	Dairy & Milk Equipments	Education Equipments
Medical & Surgical	Soil Material Testing Equipments	Microscope
Oil Petroleum Testing Equipments	Pharmaceutical Testing Equipment	Testing Equipments
Agro Food Products	Automotive Division	Machines and Tools
Generators

Content on this page requires a newer version of Adobe Flash Player.

Material Testing / Geotechnical Equipment